ABS 12 Volt Solar Panel Regulator Lithium Battery Solar Charge
Controller
Features of SR-MT2410
1. Adopting double crest or multi crest tracing technique,used for
the condition when a part of solar panel is under shadow or parts
of panel isdammage
2. Built-in maximum power point tracking algorithm which could
promote the energy utilization efficiency of pv system.The charging
efficiency is 15%~20% higher than PWM mode
3. It can find out the best working point of I-V curve within 1
minuite,the MPPT efficiency could reach to 99.9%.
4. Adopting advanced digital power supply techniques which makes
the energy conversion efficiency reach up to 97%
automatically,which enable the system to work under the rated
charging current
5. Have the fault code indication,it helps user confirm the rated
charging current.
6. Various load control methods.could recognize day and night
qutomatically.
7. Various system protection functions.including
over-charge,over-discharge,over-dischage,over-load,over-heat,battery-reverse
connection and short-circuit protection eyc.
Installation and use instruction of SR-MT2410
1. Fix the controller: Fix the controller onto the surface of the
specific place. Keep a certain distance between the controller and
fitting surface to assure heat dissipation
2. Wire preparation: Adopt the wire matching the current,plan the
length of wire, strip 5mm insulation of one side of the controller
terminal and try to decrease the length of the connected wire so
that a reduction in electrical loss.
3. Connect to the battery: connect the battery wire to the
controller firstly, Pay attention to the “+” and “–”, in case of
reverse connection. If connected well, the indicator light will be
on. Otherwise, please check the connection. If reverse connection,
controller will not working but not damage the controller.
4. Connect to the solar panel: Pay attention to the “+” and “–”,
not reverse connect. If ample sunshine, controller will show
charging mode. Or should check the connection is right or wrong. If
solar panel under the sunshine will produce voltage immediately. If
use 24V or more than 24V system, the solar panel voltage will
exceed to body safety voltage, when use please prevent you self
from electric shock.
5. Connect Load:Connected the load to controller,make sure the
current cannot over the rated current, and notice the positive and
negative electrode. Prevent the system from reverse connect.
Parameter of SR-MT2410
| Model | MT2410 |
| System voltage | 12V | 24V |
| Max. input power of solar panel | 130W | 260W |
| Transfer efficiency | ≤96% | ≤97% |
| Rated charge/ discharge current | 10A |
| No load loss | <15mA |
| Max. input voltage of solar panel | <150V |
| MPPT tracing efficiency | >99% |
| Over voltage protection | 16.5V | 33.0V |
| Limited charge voltage | 15.5V | 31.0V |
| Equalizing charge voltage | 15.2V | 30.4V |
| Equalizing charge interval | 30 days |
| Boosting charge voltage | 14.4V | 28.8V |
| Floating charge voltage | 13.8V | 27.6V |
| Over-discharge recover voltage | 12.5V | 25.0V |
| Over discharge voltage | 11.0V | 22.0V |
| Boosting charge time | 2 hours |
| Equalizing charge time | 1 hour |
| Over temperature protection | Yes |
| Light-operated voltage (on) | 5V |
| Light-operated voltage (off) | 6V |
| Light-operated delay time | 5min |
| Working temperature | -35℃~+65℃ |
| Weight | 430g |
| Altitude | ≤3000m |
| Dimension | 143*71*37.4 (mm) |
| Installation dimension | 139*48(mm) |
| Overload protection | Load current≥1.25 times rated current, cut off the load within 10
seconds; Load current≥1.5 times rated current, cut off the load
within 5 seconds |
| Protections | 1.Reverse connection. 2.Inner over temperature. 3.The voltage of PV
input terminal is over value. 4.Over load 5.Reverse charging
protection at night. 6. TVS lightning protection 7. Waterproof: IP
64 |
FAQ
1 Q: Do you have your own factory? Can we visit?
1 A: Absolutely.You are always welcomed to visit our factory.
2 Q: How do you control the quality of the products?
2 A: Our factory has obtained CE and ISO9001 certificate. Every
process of the production is strictly controlled. And all the
products will be inspected by QC before shipment.
3 Q: What kind of payment do you accept?
3 A: We accept T/T, Paypal, Western Union .
4 Q: How long the delivery time?
4 A: 2-7 days for ex-stock orders.
5 Q: What kind of controller you mainly manufacturer?
5 A: We mainly produce PWM solar charge controller, MPPT solar
charge controller.
6 Q: Can we print our company logo on product and package?
6 A: Yes,but quantity of order is required. And we also need you to
offer the Trademark authorization to us.
7 Q: How long is the warranty period?
7 A: 3 years warranty.
